- Should hi hats be mono or stereo?
- Why do my hi hats sound bad?
- How loud should my hi hats be?
- What are the best sounding hi hats?
- How do you put vocals on a pan background?
- How do you pan a drum?
- Should you pan hi hats?
- Should vocals be panned?
- How Many Mics do you need for live drums?
- Where can I pan percussion?
- Where do drums go in a mix?
- What is Pan in sound mixer?
Should hi hats be mono or stereo?
Hats usually do get some panning and/or stereo expansion.
It varies a lot from piece to piece, but hats are usually *not* left in mono.
Cymbals are usually off to the side, but like hats, the choice is up to you.
“Better” is in the end, just your own personal choice..
Why do my hi hats sound bad?
If you push too hard on your hi hat foot pedal, you will choke the cymbals – and this is a sure way to make even the best cymbals sound average. … If there is too much separation between the two, you are only getting the high pitched, and somewhat piercing sound of the top cymbal.
How loud should my hi hats be?
The thing you want to create is a “nice even sound” as when your song gets mastered the low and top end will become much louder and much more defined than before. If you absolutely must have a volume level for your hi hats, I would suggest -20 db.
What are the best sounding hi hats?
7 Best Hi-Hats for 20201 Paiste Formula 602 Modern Essentials Hi Hat Cymbals 15″: Best Hi-Hats for Versatility. … 2 Paiste Signature Dark Crisp Hi-Hat Cymbals 14″: Best Hi Hats for Recording. … 3 Zildjian A Avedis Hi Hat Cymbals 14″: Best Vintage Hi Hats. … 4 Zildjian K Sweet Hi Hat Pair 14″: Best Hi Hats for Value.More items…•
How do you put vocals on a pan background?
Wrapping Up: Mixing Background VocalsCreate a BGV master bus.Copy over the plugins from your main vocal and check for any issues.Reverse the boosts and cuts from the main vocal’s tonal EQ.Increase the compression until you are getting 5-10dB’s of gain reduction.Pan your BGVs to create space for the main vocal.More items…•
How do you pan a drum?
Simply pan your overhead mics hard left and right (as far left and right as they go), shut your eyes and listen to where you can picture these drums in front of you. Then pan the individual drum to match where they are on the overheads. This takes practice by the way!
Should you pan hi hats?
By panning hi-hats to the sides, everything that’s left in the center will get more attention, simultaneously making the mix feel wider and more rhythmic. For hip-hop and electronic tracks, I like to pan hats 30–50% away from the center. … One idea is to pan a closed hat to one side and an open hat to the other.
Should vocals be panned?
That means kicks, basses and anything else below the 120hz range. If your track has lead vocals pan them center as well. Experiment with panning duplicates of effected vocals to the left or right. But as a general rule lead vocals should always be panned center.
How Many Mics do you need for live drums?
You need to have two microphones of the same type though, and they need to be on similar sources, but for multiple toms it is a real boon as you can put up a microphone on each drum and combine them, using only one channel of the desk.
Where can I pan percussion?
Usually, I pan the hi hats, cymbals, tambourines and shakers, so the more basic percussion instruments, a little to the right and/or left of center. If 100 is hard left and hard right (=completely all the way) and 0 is center, anything between -/+ 10 and -/+ 30 will do.
Where do drums go in a mix?
The loudest element in the drum kit should be the snare drum, followed by the kick drum. The toms can also be about this volume, assuming they’re used sparingly. Close-mic’d cymbals like the hi-hat should come next. Finally, blend in the overhead and room mics to create the desired amount of space for your mix.
What is Pan in sound mixer?
Panning is the distribution of a sound signal (either monaural or stereophonic pairs) into a new stereo or multi-channel sound field determined by a pan control setting. … A pan pot has an internal architecture which determines how much of a source signal is sent to the left and right buses.