Quick Answer: Do You Push Or Pull When Welding?

What is the major difference between the push or pull technique welding?

The reason: when you push, you’re mainly watching where you’re going.

When you’re pulling, you’re mainly watching where you’re coming from.

Pulling allows you to see your bead as soon as it’s created.

Many welders prefer to immediately see how their weld is turning out..

What shade is safe for welding?

Both ANSI and AWS are more cautious, recommending a shade number 11 for welding at 60-160 amps, a number 12 for 160-250 amps, and a number 14 for 250-500 amps. Verify that both the welding helmet and lens shade meet ANSI Z87.

How dark should my welding helmet be?

It’s recommended that you use between a shade 10 to a shade 13 welding lens to prevent flash burn on your eyes. The higher the number the darker the shade will be. However, the more amperage you are using the darker the shade you will want to have to avoid burning your eyes.

Should you mig weld up or down?

To get desired results, your MIG welding gun should face the metal at 5 – 15 degrees downwards while moving down in “Z” motions.

What type of welding should I learn first?

Arc weldingThe most basic form of welding, and a great start for beginners, is Arc welding. Now there are a variety of different methods of Arc welding, although the most common processes are Metal Inert Gas (MIG) welding, Tungsten Insert Gas (TIG) welding and Stick welding.

Can you weld over slag?

You can, and you shouldn’t. Slag inclusion is a serious weld defect that can make a weld fail to perform as expected. Slag is also non-conductive, meaning it is difficult to impossible to start a weld on slag.

Can you weld over porosity?

Cleaning your surface and using the right amount of gas flow will cover most porosity issues. However, there are quite a few less-common causes for porosity. … Some welders claim you can essentially burn through the porosity by turning your amperage up over 310 and welding back through your bad weld.

How do I choose an auto darkening welding helmet?

The most important factors to consider when selecting an auto-darkening helmet are safety, comfort, convenience and style. There are a number of general selection considerations that will help welders choose a helmet that best meets their needs, as well as find one that wears comfortably all day on the job.

Can you touch the metal you are welding?

Do not rest your body, arms, or legs on the work piece (the metal being welded), especially if your clothing is wet or bare skin is exposed (and it should not be if you are dressed properly). … Do not touch the electrode or metal parts of the electrode holder with skin or wet clothing.

Is stick welding hard?

Stick welding is a good welding process, and has been around for years. … Plus you have to chip the slag from stick weld beads. And third, it can be hard to start and maintain an arc for beginners. When all you want to do is lay a weld bead, but you can’t even get the arc started it can be frustrating for beginners.

What is the correct way to MIG weld?

There are two ways to MIG weld. The first and the most common is to push the MIG gun toward the direction of the weld, this is called forehand method. Forehand welding produces shallow penetration with a flat wide smooth surface. The second is backhand method where you drag the MIG gun like a Stick welder.

How do I stop my spatter from MIG welding?

But whichever way works best for you, proper technique is essential to keeping spatter at a minimum. Optimally, you should hold the MIG gun at no more than 15 degrees from vertical. A deviation away from this can cause the shielding gas to cover the weld unevenly.

Are gasless MIG welders any good?

There’s no such thing as gasless mig welding. The weld pool has to be protected from the oxygen in the air and this is done by displacing the air with gas! So called “Gasless” Mig Wire is actually “Self Shielding”. Self Shielding Mig Wire is a tube of metal with a flux core.

What is the darkest welding shade?

13Welding shades: Determine how dark the welding filter gets when the welding arc is struck. Market standard shades are 8-13 with 13 being the darkest.

What is a push pull welding gun?

The push-pull gun was invented some years ago to prevent erratic feeding from occurring. This gun type is available from many manufacturers in both gooseneck and pistol grip styles. Whichever one you pick, the push-pull gun will incorporate a drive motor within it.

How do you push Weld?

Push or pull?The push or forehand technique involves pushing the gun away from (ahead of) the weld puddle. … With the drag or backhand technique (also called the pull or trailing technique), the welding gun is pointed back at the weld puddle and dragged away from the deposited metal.

What causes pinholes in welds?

One of the most common reasons for welding pinholes is that your cylinder is almost out of gas. This causes an uneven gas flow to the arc and creates pinholes. If there is a lot of moisture in the air, it can cause water molecules to get trapped in the weld that creates pinholes.

What causes excessive spatter in MIG welding?

Spatter is caused by several factors. The main factor is a disturbance in the molten weld pool during the transfer of wire into the weld. … In this situation, the arc is too cold to keep the wire and pool molten and causes a stubbing effect of the wire. This can occur at both high and low current ranges.